Hunterdream

4.3.3.3 Packet Tracer – Configuring VPN Transport Mode Answers Packet Tracer – Configuring VPN Transport Mode (Answers Version) Answers Note: Red font color or gray highlights indicate text that appears in the Answers copy only. Addressing Table Device Private IP Address Public IP Address Subnet Mask Site PrivateFTP server 10.44.2.254 N/A 255.255.255.0 Gotham Healthcare Branch. Cisco Packet Tracer 7.3.1 download link for Windows (10, 8.1, 7.0) 64 bits edition. Cisco Packet Tracer 7.3.1 download link for Windows (10, 8.1, 7.0) 32 bits edition. Packet tracer configure initial router settings topology objectives part verify the default router configuration part configure and verify the initial router. 6.4.1.3 Packet Tracer - Configure Initial Router Settings. Odisee hogeschool. Network Management 1 (HBI22B) Uploaded. CCNA 1 Labs - Packet Tracer 6.4.3.3 Packet Tracer – Connect a Router to a LAN Instructions Answers. Admin Send an email Oct 16, 2016. 0 / Packet Tracer – Connect a Router to a LAN. Addressing Table. Part 1: Display Router Information. Part 2: Configure Router Interfaces.

Packet Tracer – Configuring Basic EIGRP with IPv6
Addressing Table

Objectives
Part 1: Configure EIGRP for IPv6 Routing
Part 2: Verify IPv6 EIGRP for IPv6 Routing
Scenario
In this activity, you will configure the network with EIGRP routing for IPv6. You will also assign router IDs, configure passive interfaces, verify the network is fully converged, and display routing information using show commands.
EIGRP for IPv6 has the same overall operation and features as EIGRP for IPv4. There are a few major differences between them:
· EIGRP for IPv6 is configured directly on the router interfaces.
· With EIGRP for IPv6, a router-id is required on each router or the routing process will not start.
· The EIGRP for IPv6 routing process uses a “shutdown” feature.
Part 1: Configure EIGRP for IPv6 Routing
Step 1: Enable IPv6 routing on each router.
Step 2: Enable EIGRP for IPv6 routing on each router.
The IPv6 routing process is shutdown by default. Issue a command that will enable EIGRP for IPv6 routing in R1, R2 and R3.
Enable the EIGRP process on all routers and use 1 as the Autonomous System number.
Step 3: Assign a router ID to each router.
The router IDs are as follows:
· R1: 1.1.1.1
· R2: 2.2.2.2
· R3: 3.3.3.3
Step 4: Using AS 1, configure EIGRP for IPv6 on each interface.
Part 2: Verify EIGRP for IPv6 Routing
Step 1: Examine neighbor adjacencies.
Use the command show ipv6 eigrp neighbors to verify that the adjacency has been established with its neighboring routers. The link-local addresses of the neighboring routers are displayed in the adjacency table.
Step 2: Examine the IPv6 EIGRP routing table.
Use the show ipv6 route command to display the IPv6 routing table on all routers. EIGRP for IPv6 routes are denoted in the routing table with a D.
Step 3: Verify the parameters and current state of the active IPv6 routing protocol processes.
Use the command show ipv6 protocols to verify the configured parameter.
Step 4: Verify end-to-end connectivity.
PC1, PC2, and PC3 should now be able to ping each other. If not, troubleshoot your EIGRP configurations.
Configuration R1:
enable
configure terminal
ipv6 unicast-routing
ipv6 router eigrp 1
no shutdown
eigrp router-id 1.1.1.1
exit
interface g0/0
ipv6 eigrp 1
interface s0/0/0
ipv6 eigrp 1
interface s0/0/1
ipv6 eigrp 1
end
write memory
!
Configuration R2:
enable
configure terminal
ipv6 unicast-routing
ipv6 router eigrp 1

6.4.3.3 Packet Tracer Answers

6.4.1.2 Packet Tracer Answers

no shutdown
eigrp router-id 2.2.2.2
exit
interface g0/0
ipv6 eigrp 1
interface s0/0/0
ipv6 eigrp 1
interface s0/0/1
ipv6 eigrp 1
end
write memory
!
Configuration R3:
enable
configure terminal
ipv6 unicast-routing
ipv6 router eigrp 1
no shutdown
eigrp router-id 3.3.3.3
exit
interface g0/0
ipv6 eigrp 1
interface s0/0/0
ipv6 eigrp 1
interface s0/0/1
ipv6 eigrp 1
end
write memory
!

6.4 3.3 Packet Tracer Connect A Router To A Lan

6.4.3.3 Packet Tracer